RED

Take your compact camera setup to the next level by adding the Elite Accessory System for RED® KOMODO-X™. This top-tier system expands the reach of...

The Core Accessory System for RED® KOMODO-X™ is a lightweight approach to extending the camera's on-set capabilities. The system includes an ARCA B...

The Ultra Handle System is a modular, integrated system designed to adapt to any shooting style and camera build by adding or removing handle exten...

The Side Rail - Left gives users mounting points on the left side of the KOMODO® or KOMODO-X™ as well as Sensor Plane markings. This rail offers fo...

Expand your power options on the KOMODO-X™ by adding the D-Box® to your system, this D-Box converts from the camera’s native V-Mount to Gold Mount....

Micro Battery Plate Adapter V-Mount to Gold Mount (RED® V-Raptor™), designed specifically for the RED V-RAPTOR and RED KOMODO-X, converts a V-Mount...

Micro Battery Plate Adapter V-Mount to V-Mount (RED® V-Raptor™) allows users to attach full-sized V-Mount batteries to their RED V-RAPTOR and RED K...

Utilizing the tie-in points at the top end of the camera's body, this Rear Cage System provides much-needed mounting points on the rear side of the...

The Ultra Handle 4” Kit comes with the Ultra Handle Upright for RED® DSMC3™, a 4” extension, and a 1” extension. The upright has a 3-pin connector ...

The B-Box enhances the capabilities of the EXT port by offering multiple ports like Run/Stop, timecode, control, and genlock. The B-Box has eight M...

This System includes the D-Box®, B-Box, cables, and mounting options to attach the B-Box to the Rear Cage. The D-Box® offers hot swap abilities w...

The Ultra Handle Support Bracket helps stabilize longer handle configurations to prevent flexing while handle extensions are added to the camera sy...

Our line of Bolt-On Accessory Plate Adapters were designed to mount accessories that have M2.5 threaded holes to your build, like the Accessory Pla...

The Rear Cage - Left is one piece of the Rear Cage, singled out for purchasing if you only need mounting points on the left rear side of the camera...

Making use of the tie-in points at the top end of the camera's body, this Rear Cage - Right provides rear mounting points on the back and right sid...

The Side Rail - Right gives users mounting points on the right side of the KOMODO® and KOMODO-X™ as well as Sensor Plane markings. This rail offers...

The Bolt-On Rosettes give users the ability to mount Rosette Handle Grips anywhere on their build. These rosettes have locking pins to prevent twis...

The Ultra Handle Support Bracket is a lightweight, yet sturdy bracket designed to stabilize longer handle configurations and offset any flexing. T...

Developed based on a direct request from a user, the Rigging Top Plate for RED® KOMODO-X™ expands the possibilities of adding accessories to the to...

The Top Cheese Plate securely mounts to the KOMODO® or KOMODO-X™ using two ¼”-20 screws with anti-twist pins and adds seven ¼”-20, anti-twist mount...

This cable connects from the EXT port of the camera to the D-Box® for KOMODO-X™ system providing Run/Stop abilities to the 3-pin connector port.

Add ⅜”-16 and ¼”-20 mounting points on the sides of your build by attaching these sleek, lightweight Side Rails. These rails give users the flexibi...

These EXT cables connect from the D-Box® for KOMODO-X™ to the B-Box (KOMODO®, KOMODO-X, V-RAPTOR®), allowing for EXT options like Timecode, Control...

These EXT Cables connect from the camera's EXT port to the B-Box for (KOMODO®, KOMODO-X™, V-RAPTOR®) directly, breaking out control options like Ti...

The ARCA Base Plate was designed for dual 15mm LW rods and allows for maintaining optimal lens height for studio-style builds. This Base Plate come...

The ARCA Riser incorporates an anti-twist block design built into the bottom of the camera. The Riser was intended for use with the ARCA Baseplate,...

There are three options in Mount Support for KOMODO-X™ between RF to LPL and RF to PL that are compatible with the ARCA Riser for KOMODO-X. Mount s...

The Ultra Handle Upright for the RED® system has the appropriate ¼”-20 spacing for use with KOMODO-X™, KOMODO® and V-RAPTOR® cameras. This Upright...

Expand your handheld game by adding Side Grips to your setup. These grips include cold shoe mounts at the top of each handle, allowing you to mount...

IN STOCK Complete purchase by 3pm CST and order will ship same business day. All Cable-less products now ship with a 7.0+ firmware compatible board...

IN STOCK Complete purchase by 3pm CST and order will ship same business day. PL Mount (RED® DSMC1™, DSMC2™) is a simple PL mount that attaches to R...

IN STOCK Complete purchase by 3pm CST and order will ship same business day.Pass Through Top Plate provides 26pin LCD connection and 3pin trigger h...

IN STOCK Complete purchase by 3pm CST and order will ship same business day.The Revolva Pass Through Top Plate (DSMC2™) has all same features as ou...

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Trigger Handle is compatible with RED® DSMC2™ Brains (Monstro, Helium,...

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Right Side Plate (RED® DSMC2™) is a side mounting plate for RED® Weap...

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Safety NATO Arm (RED® DSMC2™) is a NATO standard side mounting arm f...

IN STOCK Complete purchase by 3pm CST and order will ship same business day.All Cable-less products now ship with a 7.0+ firmware compatible board....

IN STOCK Complete purchase by 3pm CST and order will ship same business day. Master Top Handle (Bent Handle Bracket Only) replacement front bracket...

D-Tap to 2pin Cable (18") has a standard D-Tap on one end and a 0B, 2pin connector on the other. Cable is wired in an ARRI standard configuration w...

D-Tap to 2pin Cable (12") has a standard D-Tap on one end and a 0B, 2 pin connector on the other. Cable is wired in an ARRI standard configuration ...

2pin to 2pin Cable (18") is a 0B, 2 pin cable that is wired in an ARRI standard configuration with a 18 inch cable length. 

2pin to 2pin Power Cable (12") is a 0B, 2pin cable that is wired in an ARRI standard configuration with a 12 inch cable length.

ARRI LPL Mount for RED® DSMC2™ Cameras allows ARRI LPL Signature Prime Lenses to be used with RED® DSMC2™ BRAINs with a full frame, VistaVision siz...

IN STOCK Complete purchase by 3pm CST and order will ship same business day.The AIR EVF Mount (19mm Tube Clamp Under 15mm LW Rods) slides on to an...

IN STOCK Complete purchase by 3pm CST and order will ship same business day.Master Top Handle (RED® DSMC2™) is a modular handle system designed for...

AIR EVF Mount (RED® DSMC2™ EVF) is an ultra-lightweight EVF mount for the RED® DSMC2™ viewfinder that allows for easy positioning. The system moves...